Paint Bucket Water Feature

My husband always wanted to create one of those floating water features where the tap is magically suspended above a watering can. He bought some of the supplies, but that’s as far as he got. A couple of weeks ago, I stumbled on his stash and decided to order a pump so I could make it for him.

Paint Bucket Water Feature 025_bof.jpg

Unbeknownst to him though, I wasn’t going to make just any water feature! Painting is a big part of his job so I decided to substitute the watering can he had planned to use for a paint bucket instead and take it from there.

To start, I gathered all my materials:

  • Rigid plastic tubing
  • Recycled 1 gallon plastic paint bucket with lid
  • Brass water spout
  • Pump (we use a small one; 30 GPH)
  • Clear dollar store gems
  • Chalk pencil
  • Paint brush
  • 2″ desk grommet
  • High gloss acrylic paint (be sure to get high gloss because if you want it to still look like it’s wet even once it dries!)
  • Diamond tip engraver
  • Fine hack saw or jig saw
  • 1/8″ drill bit
  • Black marker

About the Tubing

The tubing has to be rigid so it will hold the weight of the brass spout. We bought a few different sizes to test out. The first one we tried was 1/2″ interior with a 3/4″ outside diameter. It worked just fine but we thought the smaller tube we ended up using looked more realistic in terms of water flow. We used 1/4″ interior with a 3/8″ outside diameter. Keep in mind that the interior dimension of your tubing has to fit over the outlet of your pump, so take that into consideration. As an option, if you can’t find tubing with an interior diameter that fits over the pump outlet, you can always look for fittings for the pump itself to adapt it to fit the tubing.

We cut a piece of the tubing about 14 1/4″ long. The length you cut will depend on the height of your container (along with the pump once it’s attached) so cut the length of the tube to the proportion that looks good with your particular container.

We put some masking tape around the top so we could evenly mark our holes with a marker. Using a 1/8″ drill bit, hubs drilled 2 rows of holes around the edge of the plastic tube. He drilled 4 on each row for 8 holes in total – about 3/8″ down from the edge. He staggered the positioning of the holes on the second row.

Below you can see we have one row drilled and have the second row marked with the holes offset. We initially started with a larger tube, but as I mentioned, ended up using a small diameter (3/8″ instead of 3/4″).

Paint Bucket Water Feature 002_bof.jpg

Once the holes were drilled, we tested the tube on the pump to gauge the flow of the water and see how it would work. I told hubs that I was only using the paint bucket for the trial run, so we brought the tube, pump, faucet and paint bucket to our laundry room sink to give it a go. The pictures from this point forward show the 3/8″ tubing we settled on.

Paint Bucket Water Feature 014_bof.jpg

After some adjustment with the flow, we ended up putting the pump flow on a medium setting. We found that worked best for us, but you will need to do your own experimenting to see what works for you. So far so good!

Once we were happy with the mechanics of the water works, I turned my attention to the paint bucket and hubs went on his merry way – oblivious to the fact of what I was really making for him!

I took apart the grommet and used the larger side to trace a circle with the chalk pencil on the back of the can about an inch or so down from the top. Don’t put it too low because it needs to be above the final waterline which will cover the pump mechanism and you don’t want the water leaking out! I used a diamond tip engraver to trace around the circle so I’d have an outline to follow with my cutting tool.

Paint Bucket Water Feature 032_bof.jpg

I used a fine hacksaw to cut the circle out (you could also use a jigsaw with a fine blade) and  installed the larger side of the grommet into the hole to test it out. You could use some clear caulk around the edges before you permanently install the grommet to seal it. Snap the second piece of the grommet on; it provides a good strain relief for the cord and the black blends in with the bucket!

Paint Bucket Water Feature 038_bof.jpg

Moving onto the decorative steps, I first cut a piece of the sheet protector and placed it under the paint can to catch the intentional spills. It’s probably a good idea to glue it onto the bottom at this point because it’s going to be there permanently, as you’ll see later.

paint-bucket-water-feature_2

I used a glossy paint for this project because when it dries, it will still look like it’s wet and I love that look for this project. I took the paintbrush and dipped it into the paint, then painted the interior of the paint can lid. Set both the lid and the paint brush aside to dry.

paint-bucket-water-feature_3

I wanted ‘controlled’ drips around the rim and edges of the paint can so I used an eyedropper that I saved from some vitamin drops to place several paint runs around the top. You could probably just do this step with the paint brush too.

At the bottom of the can, on top of the sheet protector, I added more paint to mimic the flow of the paint spill. Once I was satisfied with the amount of paint, I set the can aside to dry.

paint-bucket-water-feature_4

I used some water proof mastic to seal the end of the tube to the faucet and also at the connection to the pump.

paint-bucket-water-feature_6

I cut a small piece of the mastic and kneaded it according to the directions.

paint-bucket-water-feature_7

I added a blob to the top of the tube, making sure that I didn’t obstruct the holes that hubs had drilled (I ended up taking some away). As you insert the tube into the faucet, take care that it doesn’t squish into the holes. Hold the two pieces together to let it set up a few minutes before you let go of it.

paint-bucket-water-feature_8

You should also connected the bottom of the tube to the pump in the same way by rolling out another piece of mastic and winding it around the connection to seal it together. I did this final step much later in the process so I could twist and position the faucet in the can once the pump was inside. Let the mastic dry for at least half an hour or the time suggested in the directions.

paint-bucket-water-feature_9

In the meantime, I slid the can onto a board and cut around the paint spill on the plastic sheet so I could removed the excess.

paint-bucket-water-feature_10

I carefully transferred the can onto a lazy suzan for my final display.

paint-bucket-water-feature_11

The bottom of the pump I purchased has suction cups on the bottom so I inserted it into the can and pressed it down against the bottom. Now you can pull the cord of the pump through the back and pop on the other half of the grommet as you saw earlier. There’s no need to seal this part; in case you ever need to remove the pump you’ll be able to get the cord out again.

paint-bucket-water-feature_12

The top of the tube will be top-heavy due to the weight of the faucet, so I added clear dollar store gems around the pump to steady it and keep it from tipping. I only purchased two bags, but could easily have doubled it! Make sure that the pump is being held securely by whatever you choose to weigh it down; you don’t want it to tip and spew water everywhere when you’re not in the room!

paint-bucket-water-feature_13

Pour enough water into the bucket to make sure the pump is fully submerged, but not so high that it will leak out of the hole you cut for the cord!

paint-bucket-water-feature_14

When it was time to pull the whole look together, I set it up in my office so I could try it out. I fed the cord down through the counter top and left it dangling until I was ready to plug it in.

paint-bucket-water-feature-079_bof

I positioned the paint lid beside the paint bucket, then leaned the paint brush on top of the lid.

Paint Bucket Water Feature 093_bof.jpg

When I plugged it in, I was amazed at how realistic it looked. It looked like real flowing water from a magically floating tap and the paint was so shiny I thought it was still wet (but it wasn’t!).

Paint Bucket Water Feature 104_bof.jpg

I couldn’t wait to surprise hub so I moved the whole shebang upstairs!

Paint Bucket Water Feature 124_bof.jpg

Hubs grinned from ear to ear when he walked into the room and saw it; I love getting surprises, but I love giving them even more! I hope he has room for this at his office; I think his co-workers would get a kick out of it – and I’ll undoubtedly need the space for my next craft project 🙂

UPDATE: Hubs loved it so much he refused to move it to the office; I’ll just have to make him another one!

Maintenance

As you run the pump, some of the water will eventually evaporate. Make sure the pump is fully covered with water; you don’t want to burn out the motor. It’s also a good idea to use distilled water instead of tap water; it will be a lot easier on the pump motor.

If you enjoyed this project, please pin and share.

Other Water Features We’ve Done

Here are two pond projects we did outside:

Back yard pond:

back-pond_garden-summer-08-052_bof

Front yard pond:

best-pond-pic-summer-08-037

If you’re interested in home and renovation projects (both indoors and out), be sure to check out our sister site, Birdz of a Feather Home.

Follow us right here on Birdz of a Feather Craft (link in footer or on homepage) or Bloglovin (link below) and you’ll get an e-mail next time I post a new  project. I’ve got some more fun things planned for 2017, like this paint stick pallet wall hanger I made hubs for Valentines Day. Get the full tutorial here, but shhh – don’t tell him!

paint-stick-pallet-wall-art-for-valentines-059_bof

Bloglovin Button

Featured on Hometalk.com
This Is How We Roll Thursday Party

Save

Advertisements

19 thoughts on “Paint Bucket Water Feature

  1. Pingback: Paint Stick Pallet | Birdz of a Feather Craft

  2. Can you explain more detail about “one row drilled and have the second row marked with the holes offset.”? Since the tubing is clear, I can not see where are the holes that you drilled.

    Your end product is very beautiful, I like to try to make one but I never do water feature before.

    Liked by 1 person

    • Thank you Joanna – have a look at the third picture from the top of the post. You can see the holes drilled just below the masking tape and then on the tape itself, the holes are marked in black marker. Once it’s drilled, it’s like a zig-zag effect because the holes on the two rows don’t line up one above the other – they are shifted.

      Like

  3. I know this is after the fact, but if you could paint the tube to match the dribbles and the puddle, it might look like it’s paint running out of the tap. You could even dye the water to match. Just a thought and your project is wonderful.

    Liked by 1 person

  4. Pingback: Indoor Gardening: Filing Cabinet Makeover | Birdz of a Feather Craft

  5. Pingback: Add Some ‘Zen’ to Your Back Garden with a Water Feature | Birdz of a Feather Home

  6. Pingback: Dental Floss Sewing Kit Hack | Birdz of a Feather Craft

  7. Pingback: Organizing a Craft Room | Birdz of a Feather Home

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s