Dog toys have a way of getting scattered throughout the house just like kids toys do. Make this dog bone basket for yourself to organize your dog toys in when you’re in the mood to tidy up or make it for any dog lover on your gift list; it also makes a great gift basket!
Just about all the materials we used to make our dog bone basket are either repurposed from items we had on hand (like the scrap of MDF we used for the base and door pulls we made into basket handles) or came from the dollar store. It’s not only unique, but it’s budget friendly too!
I started by drawing out the bone shape on paper. By folding the paper in half and only drawing out half the bone, you’ll get a more even shape once it’s cut out. I taped the paper pattern to a scrap piece of MDF and cut around it with a jigsaw. I rounded the top edges perimeter with sandpaper to smooth the sharp edges and then painted it white.
I marked the holes at 1/2″ increments about ½” in from the edge. Hubs drilled out the holes with a drill press so I could insert wooden dowels into the holes. Using a drill press is a real time saver and each hole can be drilled to the same depth for consistency. The dowels act as the ‘ribs’ of the basket to support the weaving.
I dabbed one end of each dowel into a bit of glue before inserting them into the holes.
Once all the dowels were glued, I let it dry 24 hours. Then it’s time to start weaving!
I made this basket for our friend’s new dog, which is tan and black, so I thought I’d match up the colour of the basket by combining the dollar store twine with some black yarn I had leftover from a knitting project.
Tie a knot and attach the combined twine and yarn to the middle dowel at one end of the bone.
Begin weaving in and out around the entire shape.
When I got back to where I started, I continued in the same direction. Note that if you have an odd number of dowels, you’ll be able to keep going around and around.
However, if you end up with an even amount of dowels, you’ll have to double back and turn around when you reach where you started. Have a look at the plant basket below that I made previously to see how to ‘double back’. You can see that towards the top, I looped around both dowels just to stabilize and hold the corner together.
Our friend named the new pup Dot, so I added a charm with the letter ‘D’ to the centre of the basket on the front. I opened up the link using two needle nose pliers and then squeezed it closed again around the twine and continued weaving.
When you’re about an inch from the top of the dowels and you’re back to where you started, bring the end of the twine to the inside of the basket, but don’t cut it off. To finish off the top and create a nice edging, use a thicker piece of rope: fold it in half and loop it around the same dowel.
Crisscross the rope around the dowels all the way around the perimeter of the bone until you’re back at the beginning again.
To end the edging, bring both pieces of rope to the inside of the basket. You’ll use the end of the twine to wrap around the rope and finish it off.
Wrap the twine around the rope ends in a figure eight until it’s the length of the inside wall of the basket.
Knot the twine and add some hot glue to secure the end to the back of the rope where it won’t be seen. Cut the end of the twine and the rope, then use hot glue to secure the rope to the inside of the basket so it blends in seamlessly. You can glue down the edge of the rope as well as putting a dollop on the base of the basket to keep the ends from lifting.
To finish off the top of the dowels, I blackened the ends with black marker then glued on some wooden beads.
The holes in the dollar store beads tend to be very inconsistent so I used my thin needle nose pliers to ream out the holes, making sure they would fit onto each dowel before I glued them in place. If you want to be picky about it, you can use a tiny wire brush to clear any debris from the holes before gluing on the beads.
I added a dab of hot glue to the underside of a bead and then threaded it onto the dowel, continuing around until all the dowels were capped.
In the planter basket I showed you above, I incorporated rope handles into that one so it could be lifted. Since this basket is much larger and heavier, I decided to repurpose some door pulls instead. They were originally saved from our old cabinets and were yellow oak with gold metal.
I painted them up to coordinate with the charm (I painted the oak black, then silver leafed and distressed the metal with more black). Hubs gave them a quick spray coat of varnish in the garage, which we let dry, before I mounted them onto the basket.
Measure to get both handles evenly positioned on each side the basket, ensuring you don’t cover up the charm on the front! You can insert toothpicks where you want the screws placed. I used some washers on the inside of the basket before feeding the screws through the weave of the basket. Use the toothpicks or thin needle nosed pliers to guide the screws through the weave and position the handles on each side. You’ll need a short screwdriver to attach the screws to the handles as the width is pretty narrow in the centre.
As a last step, shave off some of the longer sisal strands with scissors to neaten it up.
The basket is now done and ready to fill with dog treats – and of course a flea and tick collar to protect the pup and keep her safe!
We inserted a card and then wrapped it all up with some cellophane.
You may not have noticed, but halfway through this project, I went from working on my dining room table to my own craft studio – courtesy of all the hard work hubs put into finishing off our basement! I’m so excited to finally have a dedicated place in the house to repurpose and craft to my heart’s desire. My new studio boasts a focal point made of repurposed kitchen cabinets to hide away my stash! Check out the reveal of my new studio!
If you enjoyed this project, please pin and post on Facebook! And don’t forget to follow me here on Birdz of a Feather Craft (link on homepage) or Bloglovin’ (link below)!